Sold Out
The Cable Prowler combines the functions ofa high-end cable tester and length measurement tester, with the capability to identify link status, link capability, andPoE detection. All of this is in full color and internal memory to save results.
The Cable Prowler provides full cable testing on any category network, coax, or telephone cable. It will display wire map, numbered ID remotes, and any faults, including shorts, opens, miswires, split pairs, and reverses. The full-featured Cable Prowler measures cable length (using TDRtechnology) and generates tone levels for signal tracing andcable identification on all pairs, a selected pair, or a selected pin. All of this is displayed in a full color graphical display for easy viewing in any environment. CableProwler also has the ability to name each cable and save alltest results. Cable results can be exported to a computer via micro USB cable for record keeping and printing.
The Cable Prowler enables quick identification of a network drops link capability and current link status. CableProwler also detects the presence of PoE on the network dropand what class of PoE per IEEE 802.3 af/at with load test for voltage drop. These network tests can also be saved for record keeping and printing.
| Measurement Technology | Time Domain Reflectometry (TDR) |
| Cable Measurements | Cable Testing and ID: up to 305 m Split Pair Detection: 1 m to 305 m Length Measurement: 0 to 457 m, ± 5% Supports 8 continuity and ID number remotes (RJ-45) Supports 20 RJ-45 and 20 F-connector ID only remotes |
| Power over Ethernet | Tests for IEEE 802.3af and IEEE 802.3at (PoE Plus)compliant PoE Tests for classes and loads cable up to 25.5 watts (at class 4) Identifies Mode A or B (pairs with PoE) |
| Active Ethernet | Indicates advertised speeds of 10/100/1000base-t half or full duplex Can Link to network at 10/100base-t |
| Maximum Voltage | Parameters refer to the maximum voltage that can be applied to any 2 connector pins without causing damage tothe tester. −RJ Jack: 66 Vdc or 55 Vac −F-connector: 50 Vdc or Vac |
| Save Test Results | Stores up to 250 Cable or network tests with user defined names |
| Tone Generation | Tone Frequencies: 730 Hz and 1440 Hz |
| Languages | English, French, Spanish, German, Italian |
| Battery Life | For 6 x AA, 9VDC, 2,200 mA-hr (typical) alkaline battery: Operating ? 20 hours typical Standby ? 1.5 years typical (200uA max standby current) Batteries are included |
| Altitude | 3048 m operating |
| Temperature | Operating: 0 to 50°C Storage: -30 to 60°C |
| Humidity | 10 to 90% non-condensing |
| Enclosure | High-strength PC/ ABS plastic with V0 rating with boot Withstands 4 foot drop on to concrete |
| Size | 4.7 x 9.15 x 17.3 cm |
| Weight | With batteries: 510 g |
| Safety Compliances | CE |
| Warranty | 1 Year |
Q. What is VoP?
A. The Cable Prowler uses Time Domain Reflectometry to measure cable length and the distance to faults. VoP is the signal percentage compared to the speed of light. To calibrate the VoP, please refer to page 13 of Cable Prowler instruction manual.
Q. What does "Split" mean?
A. A cable can be wired with correct continuity but not withcorrect pairing. This most often happens when the cable is terminated consistently at both ends, but in the wrong order. The Cable Prowle will display "Split" next to the pair(s) that are not paired correctly.
Q. What is an "Open"?
A. Cable Pair(s) do not have continuity throughout the cableor the Cable Prowler? remote is not detected. An open condition will be displayed in the wire map diagram.
Q. What is a "Short"?
A. Cable Pair(s) are making an electrical connection with each other or foreign object.
Q. Why are the lengths different for each pair?
A. Due to the varying twists of each pair, their length will differ.
Q. What's the difference between the remotes?
A. The Network Telephone test remotes (black remotes with the white label) are used for performing a cable test and providing an ID. The small yellow remotes will provide an IDonly. You can also use the coax remotes to perform a test and obtain an ID for coax cables.
Q. Why doesn't the Cable Prowler show PoE Results?
A. Make sure the PoE test is on. If the "PoE Off" soft key icon is displayed, press the soft key below it to activate the PoE test. If PoE results are not displayed with when thePoE test is on, check your switch to verify that PoE is enabled.
Q. What does Link Flow Control mean?
A. Link Flow control is a switch configuration feature that pauses data transmission when there is system congestion. The Cable Prowler? identifies if this feature is enabled on the switch.
Q. What are FDX and HDX?
A. FDX is an acronym for Full duplex. HDX is an acronym for Half Duplex.
Q. Why doesn't the Application detect my Cable Prowler?
A. Make sure your Cable Prowler? is powered on and plugged into your computer using a micro USB cable. While plugged in to your PC, turn the Cable Prowler off then back on.
Q. There was an error when I attempted to update the Firmware
A. If the Cable Prowler is still on, click on "Begin Download" on the application again.
Q. My Cable Prowler won't turn on after I updatedthe Firmware.
A. An error occurred during the Firmware installation but don't worry, it's still in boot loader mode (program mode). Unplug the Cable Prowler, close the application, then plug the Cable Prowler back in to your PC. Open the application and follow the Firmware update instructions. The Cable Prowler? screen will remain dark until it has been successfully updated.
Q. How do you test an Ethernet cable via Ethernet wall plate/server/router ports?
A. The 12inch Ethernet Patch Cable (CA016) allows you to connect to an RJ45 plug to test a shielded or non-shielded Ethernet cable.
Q. How do I test unterminated Ethernet cables?
A. The 8-way Alligator Clip Cord Set (CA015) allows you to test unterminated Ethernet cable. This unique cord set has an RJ45 plug on one end and an alligator clip connected to each wire on the other end. This accessory allows you to make sure cables have not been damaged before you spend the time and money to terminate them.
Q. How do I extend the life of my RJ45 Jack?
A. The Sacrificial RJ45 Cable (CA014) extends the life of the RJ45 jacks on your tester and remote(s). Plug the sacrificial cable into the tester or remote and then plug the cables to be tested into the sacrificial cables. Continue testing cables with the sacrificial cables plugged into the tester or remote(s). If the sacrificial cables become worn or damaged, simply replace them. This prevents downtime and saves money by not having to send your tester in for an RJ45 jack replacement.
Q. How do I test cables with BNC connectors?
A. The F-jack to BNC jack allows you to easily test coax cables that have been terminated with BNC connectors.
